Product Usage

Click on any product below to see the usage instructions from the label.

Label Instructions:
It is extremely important that DRI WASH 'n GUARD® be applied with the AIRosol sprayer only. Use on hard, non-porous surfaces only. Pre-test on inconspicuous area before use. Can be used over surface containing moderate level of dust, dirt, road grime or salt.
Refill Procedures:
  • Unscrew collar nut at neck of AIRosol bottle and remove internal spray mechanism
  • Invert bottle of product, shake vigorously for 15-20 seconds
  • Pour contents into AIRosol bottle until 75% full
  • Re-Install spray mechanism and collar nut
Directions By Hand:
  1. Apply Dri Wash 'n Guard® to a cool, dry surface in a shaded area. Avoid windy conditions if possible.
  2. Use two soft, clean terry cloth towels... one for cleaning/polishing and one for buffing.
  3. Invert the bottle and shake vigorously for 15-20 seconds.
  4. Pressurize the bottle by pumping the cap up and down until a strong resistance is felt (approx. 10-15times).
  5. Spray a generous coat of Dri Wash 'n Guard® on a small section of vehicle (2-3 sq. ft.), spraying with a broad sweeping motion where possible.  On windows, apply a light coat.
  6. With moderately firm pressure, rub DWG thoroughly over the sprayed area until the filmy haze that appears almost disappears.
  7. Buff the remaining haze to a high gloss with second terry cloth towel
Directions by Machine:
  1. Use a conventional or orbital-type buffer equipped with a foam polishing pad. Do not exceed 2,400 RPM.
  2. Apply Dri Wash 'n Guard® as described in steps 3, 4, and 5 above.
  3. Immediately buff sprayed area to a high gloss.
  4. Continue, section by section, until all accessible areas have been buffed.
  5. Polish any remaining areas by hand, if necessary.

For ultimate surface restoration, use DRI WASH 'n GUARD® OxygoneTM as Step 1, and DRI WASH 'n GUARD® Waterless Car Wash and Protective Glaze as Step 2.

Caution: Use under well ventilated conditions.

First Aid Treatment:  If swallowed, call physician or poison control center immediately.  Contains petroleum distillates.

Label Instructions:

It is extremely important that DRI WASH 'n GUARD® ULTRA-ION be applied with a DRI WASH 'n GUARD® Car AIRosol pump sprayer only. Use on hard, non-porous surfaces only. Pre-test on inconspicuous area before use. Can be used over surface containing moderate level of dust, dirt, road grime or salt.

Refill Procedures:
  • Unscrew collar nut at neck of AIRosol pump sprayer and remove internal spray mechanism
  • Invert bottle of product, shake vigorously for 15-20 seconds
  • Pour contents into AIRosol pump sprayer until 75% full
  • Re-Install spray mechanism and collar nut
Directions By Hand:
  1. Apply Dri Wash 'n Guard® ULTRA-ION to a cool, dry surface in a shaded area. Avoid windy conditions if possible.
  2. Use two soft, clean terry cloth towels... one for applying the product and one for buffing.  For best results, use the DWG Buffing Towel for buffing.
  3. Invert the AIRosol pump sprayer and shake vigorously for 15-20 seconds.
  4. Pressurize the bottle by pumping the cap "up and down" until a strong resistance is felt (approx. 10-15 times).
  5. Spray a light coat of Dri Wash 'n Guard® ULTRA-ION on a small section of vehicle (2-3 sq. ft.), spraying with a broad sweeping motion where possible.
  6. Using the terry cloth towel, with moderately firm pressure, rub polish thoroughly over the sprayed area until the filmy haze that developed almost disappears.
  7. Buff the remaining haze to a high gloss with the DWG buffing towel.
Directions by Machine (FOR PROFESSIONALS ONLY):
  1. Use a conventional or orbital-type buffer equipped with a foam polishing pad. Do not exceed 1,500 RPM.
  2. Apply Dri Wash 'n Guard® ULTRA-ION as described in steps 3, 4, and 5 above.
  3. Immediately buff sprayed area to a high gloss.
  4. Continue, section by section, until all accessible areas have been buffed.
  5. Polish any remaining areas by hand, if necessary.

For ultimate surface restoration, use DRI WASH 'n GUARD® OxygoneTM as Step 1, and DRI WASH 'n GUARD® ULTRA-ION Waterless Car Wash and Protective Glaze as Step 2.

Caution: Use under well ventilated conditions. Prevent product from freezing. DO NOT MIX THIS PRODUCT WITH ANY OTHER CHEMICAL OR WATER.

First Aid Treatment:  If swallowed, call physician or poison control center immediately.  Contains petroleum distillates.

Label Instructions:

DO NOT use on glass, floors, or painted surfaces.
DO NOT mix this product with any other chemicals or liquids.

For best results, pre-test on inconspicuous area before use.

Directions:

1. Use one soft, clean terry cloth towel or soft bristle brush for cleaning, and another for drying.
2. Invert bottle and shake once or twice.
3. Spray area to be cleaned from a distance of 8-10 inches.
4. Agitate sprayed area with soft, clean, terry cloth towel or bristle brush.
5. Pat dry with soft, clean, terry cloth towel.
6. Allow area to completely dry.

Caution: Keep out of reach of children.

First Aid Treatment: If swallowed, call physician or poison control center immediately.

Label Instructions:

DO NOT use on glass, Plexiglas, mirrors, chrome or other non-porous surfaces.
DO NOT use in an area where painting occurs or on surfaces that may require painting.
DO NOT mix this product with any other chemicals or liquids.

First: Replace shipping cap with trigger sprayer (included).

Directions:

1. Use one soft, clean cloth for cleaning/polishing and another for buffing.
2. Invert bottle and shake once.
3. Rotate nozzle to "SPRAY" position.
4. Spray generously onto surface from a distance of approximately 8-10 inches.
5. Immediately polish the are with a soft, clean cloth. The use of a small, soft bristle brush may be helpful in penetrating rough or uneven surfaces such as tire sidewalls.
6. Buff to a shine using a second soft, clean cloth.
7. Repeat process for higher luster and longer lasting protection.

Caution: Keep out of reach of children.

First Aid Treatment: If swallowed, call physician or poison control center immediately.

Label Instructions:

DRI WASH ‘n GUARD® Leather and Vinyl Treatment contains no petroleum distillates, soaps or detergents.  It is non-corrosive, non-flammable, and non-caustic.

DO NOT use on glass, floors, woven materials or painted surfaces.
DO NOT mix this product with any other chemicals or liquids.

For best results, pre-test on inconspicuous area before use.

1. Use one soft, clean terry cloth towel or sponge for cleaning, and another for buffing.
2. Invert bottle and shake once or twice.
3. Spray area to be cleaned from a distance of 8-10 inches.  To prevent overspray, apply to an area no larger than 18 inches.
4. Rub sprayed area with a soft, clean terry cloth towel or sponge.  (For excessively soiled areas, scrub lightly with a soft brush and then rub with a clean soft terry cloth towel or sponge.)
5. For best results, buff lightly with a clean, terry cloth towel.

Caution: Keep out of reach of children.

First Aid Treatment: If swallowed, call physician or poison control center immediately.

Label Instructions:

DO NOT use on thin plated metal surfaces. DO NOT use near heat, sparks, or flame.
DO NOT breath vapors for extended periods.
DO NOT mix this product with any other chemicals or liquids.

For best results, pre-test on inconspicuous area before use.

Directions:
  1. Use two soft, clean terry cloth towels... one for cleaning/polishing and one for buffing.
  2. Invert bottle and shake vigorously before and during use.
  3. Apply a small amount of DRI WASH 'n GUARD® Premium Metal Polish on a clean terry cloth towel.
  4. Rub surface lightly until polish turns dark.
  5. Let dry and buff with a separate clean, terry cloth towel.
  6. For maximum protection, apply DRI WASH 'n GUARD® Waterless Car Wash and Protective Glaze after treatment.

Caution: Use under well ventilated conditions.

First Aid Treatment: If swallowed, call physician or poison control center immediately. Contains petroleum distillates.

Label Instructions:

For best results, pre-test on inconspicuous area before use.

Directions By Hand:
  1. Invert bottle and shake vigorously for 5 seconds
  2. Apply a small amount of OxyGoneTM on a clean terrycloth towel.
  3. Using the towel, work the product into the oxidized surface until haze begins to disappear.
  4. Using another clean terry cloth towel, buff the treated surface to a gloss.
  5. For best results, work in small sections.

For ultimate surface restoration, use DRI WASH 'n GUARD® OxygoneTM as Step 1, and DRI WASH 'n GUARD® Waterless Car Wash and Protective Glaze as Step 2.

Directions by Machine:
  1. Invert bottle and shake vigorously for 5 seconds.
  2. To prevent splatter, apply a small amount of OxyGoneTM on a clean terrycloth towel and spread over a 12" area.
  3. Buff to a high gloss using a conventional or orbital-type buffer equipped with a foam polishing pad. Do not exceed 2,400 RPM.

Caution: Use under well ventilated conditions.

First Aid Treatment: If swallowed, call physician or poison control center immediately. Contains petroleum distillates.

Label Instructions:

DO NOT use on glass, Plexiglas, mirrors, chrome or other extremely porous surfaces.
DO NOT use in an area where painting occurs or on surfaces that may require painting.
DO NOT mix this product with any other chemicals or liquids.

Directions:
1. Test in a discrete area before general use.
2. Invert bottle and shale once.
3. Spray onto surface from approximately 10 inches away.
4. Some surfaces may require immediate polishing with a soft clean cloth.
5. Heavy dust build-up may require a second application.

Caution: Keep out of reach of children. Do not ingest. If ingestion occurs, contact a physician. Avoid contact with eyes. If contact occurs, flush with water for 10 minutes. If skin irritation occurs, wash with soap and cool water. If irritation persists, discontinue use and contact a physician.

Label Instructions:

DO NOT use on chrome-coated plastic or vinyl flooring.
DO NOT use on vehicle exteriors. Painted surfaces treated with the product may discolor when exposed to outdoor sunlight.

Tips:

No need to "pre-clean" surfaces before using DRI WASH ‘n GUARD® For The Home. Let our product do the cleaning for you!
Surfaces must be completely dry before applying.
Between applications, wipe with a damp terry cloth towel and buff with a dry terry cloth towel.

Directions:

1. Invert aerosol can and shake vigorously.
2. Use two soft, clean terry cloth towels... one for cleaning/polishing, and one for buffing.
3. Spray a light coat of DRI WASH ‘n GUARD® For The Home directly onto dry surface.
4. With moderate firm pressure, rub polish thoroughly over the sprayed area until the filmy haze that develops almost totally disappears.
5. Immediately buff remaining haze to a high gloss with second terry cloth towel.

Caution: Use under well ventilated conditions. Contents under pressure. Do not use near fire, sparks, or open flames. Do not puncture or incinerate container. Exposure to temperatures above 130 degrees F may cause bursting.

First Aid Treatment: If swallowed, call physician or poison control center immediately. Contains petroleum distillates. In case of eye contact, immediately flush eyes with water, remove any contact lenses, and continue to flush eyes with plenty of water for at least 15 minutes. If irritation continues, contact a physician.

Customer Support

Support Topics


Connect Live

Google Talk Logo
Get Live Help
via Google Talk!
Simply start a
conversation with
john.skurka@gmail.com



Windows Live Messenger
Get Live Help
via Windows Live Messenger!
Simply start a
conversation with
driwashnguard@live.com



Windows Live Messenger

Get Live Help
via AOL Instant Messenger!
Simply start a
conversation with
DriWashed

Our Guarantee

If you're not completely satisfied with the performance of any DRI WASH 'n GUARD® waterless product purchased at DriWashSolutions.com, we'll give you your money back - no questions asked.

So what do you have to lose? Just the cost of shipping.

Simply return the unused portion to us within 30 days of purchase, along with a copy of your receipt, and we'll send you your money back. Please note that shipping is not refundable.

Any questions please call us at (888) DRI-WASH from 8:00 am to 8:00 pm (Eastern Standard Time) or contact us via e-mail.

Return unused portion of product by UPS or FedEx to:

DriWash Solutions
8 Brooktree Lane
Ithaca, NY 14850

Note: be sure to include a copy of your receipt with your return.